Kraang Finds
More ▾
Products About
Maker Gear

6 Cutting Tools Every Maker Uses Weekly

A detail knife, a self-healing mat, a cork-backed steel rule, a rotary cutter, a snap-off knife and flush cutters — the cutting kit that gets used every week.

Published October 31, 2026 · 6 picks

A maker bench with a cutting mat, hobby knife, steel ruler, rotary cutter, snap-off knife and flush cutters

At a glance

6 picks
  1. 1
    Fiskars 6" Detail Craft Knife (167110-1001)
    Amazon
  2. 2
    Fiskars 18" x 24" Self-Healing Cutting Mat, Gray
    Amazon
  3. 3
    Westcott 10417 Stainless Steel Ruler with Cork Base, 18 in
    Amazon
  4. 4
    OLFA 45mm Quick-Change Rotary Cutter (RTY-2/C), Aqua
    Amazon
  5. 5
    OLFA L-1 18mm Heavy-Duty Snap-Off Utility Knife
    Amazon
  6. 6
    KNIPEX 78 03 125 Electronics Super Knips, 5-Inch
    Amazon

As an Amazon Associate I earn from qualifying purchases. If you buy through a link on this page we may earn a small commission, at no extra cost to you. How this works.

1 Fiskars

Fiskars 6" Detail Craft Knife (167110-1001)

A pen-sized knife for templates, decals and cleaning up small parts.

Best for Cutting templates and stencilstrimming vinyl and cardstockcleaning up models and prints

A precision knife is the tool that gets picked up most often on a maker bench: a template to cut out, a vinyl decal to weed, a burr on a 3D print, a stencil, a slot in a foam-board prototype. It holds like a pen, so the cut follows your hand instead of fighting it.

The Fiskars detail knife is the classic aluminum hobby-knife layout with one useful addition, an orange SoftGrip pad right where your fingertips press. That matters on longer sessions. It uses the same standard blades as other hobby knives, so a fresh #11 is never hard to find.

Pro tip Change the blade the moment it starts to drag or tear paper fibers. A dull blade needs more pressure, and extra pressure is what makes a knife slip.

Why we like it

  • ✓Aluminum body with a SoftGrip pad where your fingers sit
  • ✓Takes standard
  • ✓Comes with a
  • ✓Full lifetime warranty on the handle, per Fiskars (blades excluded)

Keep in mind

  • !Ships with a single blade — budget for a pack of
  • !Not for thick card or foam board — reach for a snap-off cutter there
Model
167110-1001
Length
6.2 in (158 mm)
Handle
Aluminum, SoftGrip pad
Blade included
#11
Compatible blades
#10, #11, #16, #17
Weight
1.8 oz
2 Fiskars

Fiskars 18" x 24" Self-Healing Cutting Mat, Gray

Saves the bench and the blade, and its grid doubles as a quick square.

Best for Knife and rotary cuttingmeasuring and squaring partsprotecting the bench top

Every knife and rotary cutter on this list needs something under it. A self-healing mat grips the blade just enough for a controlled cut, then closes up so the next cut doesn’t follow an old groove. It also saves the bench top and the tip of your blade.

The 18 x 24 in size is the practical middle: big enough for a full sheet of card or a fat quarter of fabric, small enough to leave room on the bench. The printed grid is the hidden bonus — it doubles as a quick way to square a part or measure a cut without reaching for a ruler.

Pro tip Don’t cut on the same grid line every time. Spread your cuts across the mat, and flip it over now and then, so no single spot wears into a trench.

Why we like it

  • ✓Self-healing surface closes up after knife and rotary blade cuts
  • ✓Inch grid on both sides, so you can flip it when one side wears
  • ✓30°, 45° and 60° angle lines for bevels and miters
  • ✓Big enough for a full sheet of letter paper with room to spare
  • ✓Full lifetime warranty, per Fiskars

Keep in mind

  • !Warps if left in a hot car or in direct sun — store it flat
  • !Not for hot glue, soldering or heat guns; heat marks don't heal
Size
18 x 24 in (46 x 61 cm)
Sides
2, gridded
Grid
Inch, with 30/45/60° bias lines
Material
Plastic, self-healing
Weight
1.5 lb
Care
Warm water and mild soap
3 Westcott

Westcott 10417 Stainless Steel Ruler with Cork Base, 18 in

A steel edge for the knife to follow, with cork so it doesn't slide.

Best for Guiding knife cutsmeasuring in inches and millimetersscoring foam board and card

A hobby knife or snap-off cutter is only as straight as the edge it follows. Plastic rulers get shaved by the blade, and a bare steel ruler slides at the worst moment. A cork-backed steel rule fixes both: the blade rides along metal, and the cork grips the mat while you press down.

The Westcott 10417 is a plain office-grade stainless ruler with inch and metric scales, which is exactly what a cutting guide needs to be. At 18 in it reaches across most sheets of card, foam board and vinyl in one pass.

Pro tip Put your fingers on the ruler, not near its edge, and keep the knife on the side of the ruler away from them. If the blade slips, it slips away from your hand.

Why we like it

  • ✓Stainless steel edge holds up to blades, unlike plastic or wood rulers
  • ✓Cork backing keeps it from sliding on the mat
  • ✓Inch (1/16) and metric scales on the same ruler
  • ✓Hang hole for storage on a pegboard
  • ✓Limited lifetime warranty, per Westcott

Keep in mind

  • !Thin and flexible, so it's a cutting guide, not a reference square
  • !Cork lifts the edge slightly off the surface — keep the blade upright against it
Model
10417
Length
18 in (approx. 18.25 x 1.25 in overall)
Material
Stainless steel, cork back
Scales
1/16 in and metric
Extras
Hang hole
4 OLFA

OLFA 45mm Quick-Change Rotary Cutter (RTY-2/C), Aqua

Rolls through fabric, felt and foam in one straight pass.

Best for Cutting fabric and feltthin leather and craft foamlong straight strips against a ruler

A knife pulls fabric, felt and foam as it cuts, so long cuts go wavy. A rotary cutter rolls instead of dragging: the blade presses straight down and travels along the ruler, which gives clean, square edges on cosplay foam, felt, leather strips and fabric.

The RTY-2/C is OLFA’s 45 mm quick-change cutter, the standard size for most craft work. The quick-change system means the blade comes out without a pile of tiny parts, which makes it more likely you’ll actually swap a dull one.

Pro tip Close the blade cover after every single cut, even if you’re about to make another one. A rotary blade is exposed on all sides, and most injuries happen when an open cutter is set down on the bench.

Why we like it

  • ✓45 mm tungsten tool steel blade (RB45) comes installed
  • ✓Quick-change system for faster, safer blade swaps
  • ✓Built-in blade cover slides over the edge between cuts
  • ✓Contoured handle with finger grooves; works left- or right-handed
  • ✓OLFA says it cuts up to 8 layers of cotton fabric

Keep in mind

  • !Blade cover is manual — you have to remember to close it every time
  • !Needs a cutting mat; on a bare bench it dulls the blade almost instantly
Model
RTY-2/C
Blade
45 mm RB45, tungsten tool steel
Handle
Plastic, finger grooves, hang hole
Hand
Left or right
Cuts
Fleece, felt, wool, cotton, leather, suede, foam, vinyl
Weight
1.6 oz
5 OLFA

OLFA L-1 18mm Heavy-Duty Snap-Off Utility Knife

Snap off a segment and the tip is sharp again — for cardboard, foam board and rubber.

Best for Cardboard and foam boardrubber and gasket materialopening boxes of supplies

The hobby knife handles detail; the snap-off cutter handles everything thicker. Cardboard for a prototype, foam board, craft rubber, gasket material, and the endless boxes that supplies arrive in. When the tip goes dull, you break off one segment and the next one is factory sharp.

The L-1 is OLFA’s long-running heavy-duty 18 mm knife. The ratchet wheel locks the blade at the exact length you want, which is the main thing that keeps a snap-off blade from wobbling.

Pro tip Snap segments off with pliers or a blade snapper, never with bare fingers, and drop the used pieces into an old jar or tin. Loose segments on the bench are a hazard for the next person who reaches across it.

Why we like it

  • ✓18 mm blade with 8 snap-off segments, so a fresh tip is always one snap away
  • ✓Ratchet wheel locks the blade at any length you set
  • ✓Stainless steel channel holds the blade steady in the ABS handle
  • ✓Lanyard hole for tethering

Keep in mind

  • !Ratchet wheel is slower to adjust than a simple slider
  • !Extended blade can flex on deep cuts — keep only as much out as the material needs
Blade
18 mm LB snap-off, 8 segments, Japanese carbon tool steel
Lock
Ratchet wheel
Handle
ABS plastic, stainless steel channel
Extras
Lanyard hole
Weight
2.5 oz
6 KNIPEX

KNIPEX 78 03 125 Electronics Super Knips, 5-Inch

Flush cuts on leads, zip ties and sprues, with tips that reach right up to the part.

Best for Trimming component leadscutting zip ties flushsnipping model sprues and fine wire

Flush cutters are the snips of the maker bench: component leads after soldering, the tail of a zip tie, sprues on a model kit, a stray support on a print. A flush cutter leaves a flat end instead of a pinched point, so there’s nothing sharp left sticking out.

The Super Knips is KNIPEX’s fine electronics cutter, with an opening spring and narrow tips that slip between parts on a crowded board. It’s a precision tool, so it lives in the drawer for fine work, not for hardware store wire.

Pro tip Wear glasses when trimming leads, and cover the cut end with a finger. Short copper offcuts fly surprisingly far, and they always seem to find an eye or the inside of a power supply.

Why we like it

  • ✓Ground cutting edges with no bevel, for a truly flush cut
  • ✓Precision tips cut close-sitting wire down to 0.2 mm
  • ✓Opening spring with restricted opening, so it stays in your hand
  • ✓Smooth joint designed to reduce hand fatigue, per KNIPEX

Keep in mind

  • !For soft copper wire and plastic only — piano wire or screws will chip the edges
  • !The fine tips are easy to spring if you twist while cutting
Model
78 03 125
Length
5 in (approx. 5.1 in)
Cut
Flush, no bevel
Capacity
Up to 1.6 mm soft wire
Edge hardness
Approx. 54 HRC
Standard
DIN ISO 9654
Weight
2.1 oz

More Maker Gear