Kraang Finds
More ▾
Products About
Maker Gear

7 Desk Organizers for Small Parts and Screws

Drawers, a magnetic tray, a divided box, a repair tray, a label maker, a louvered wall panel and a steel pegboard — so every screw has a place.

Published October 31, 2026 · 7 picks

A maker desk with a parts cabinet, label maker, divided screw box, magnetic tray, project tray, pegboard and louvered wall bins

At a glance

7 picks
  1. 1
    Akro-Mils 10116 16-Drawer Storage Cabinet
    Amazon
  2. 2
    GRIP 6-Inch Stainless Steel Magnetic Parts Tray
    Amazon
  3. 3
    iFixit Anti-Static Project Tray
    Amazon
  4. 4
    Flambeau 4007 Tuff Tainer with Zerust Dividers
    Amazon
  5. 5
    Brother P-touch PT-D220 Label Maker
    Amazon
  6. 6
    Akro-Mils 30618 Louvered Steel Wall Panel (4-Pack)
    Amazon
  7. 7
    Wall Control 30-P-3232B Metal Pegboard (2 Panels)
    Amazon

As an Amazon Associate I earn from qualifying purchases. If you buy through a link on this page we may earn a small commission, at no extra cost to you. How this works.

1 Akro-Mils

Akro-Mils 10116 16-Drawer Storage Cabinet

Sixteen clear drawers for the parts you use every week, right on the desk.

Best for Screws and nuts at the deskelectronic componentsbeads and craft partsspare 3D printer parts

A big parts cabinet on the wall is great until you need three kinds of screws for the job on your desk and keep getting up to fetch them. A small cabinet within arm’s reach holds the parts you use every week: the M3 screws, the common nuts, a few connectors and the spare nozzles.

The 10116 is the compact one in the Akro-Mils line — 16 clear drawers in a cabinet about the size of a shoebox standing on end. Dividers come with it, and it can stack on another cabinet or hang on the wall when the desk gets crowded.

Pro tip Use the drawer divider to split each drawer by length — short screws in front, long ones in back. You’ll grab the right size without dumping the drawer out.

Why we like it

  • ✓Desk-sized footprint — about 10.5 × 6.5 in
  • ✓Clear drawers show what's inside before you open them
  • ✓Drawer dividers included, molded into the back of the cabinet
  • ✓Stacks with other Akro-Mils cabinets or hangs on keyhole slots
  • ✓Rear stop tabs keep drawers from sliding out and spilling

Keep in mind

  • !Sixteen drawers fill up fast — it's a desk cabinet, not the main parts store
  • !Drawers are small and shallow, too tight for tools or bigger hardware
Drawers
16
Size
10-1/2 × 6-1/2 × 8-1/2 in (W × D × H)
Drawer (outside)
6 × 2-7/32 × 1-9/16 in
Material
High-impact plastic
Mounting
Stackable, wall keyholes
Model
10116
2 GRIP

GRIP 6-Inch Stainless Steel Magnetic Parts Tray

Steel screws dropped in here stay put, even when the tray gets bumped.

Best for Disassembly screwsnuts and washers3D printer maintenancecar and bike repairs

The moment a project comes apart, screws start rolling. A magnetic tray is the simplest fix: anything steel you drop into it stays there, even if the tray gets knocked or tilted. It’s equally useful at the desk, on the printer, or on the fender of a car.

GRIP’s tray is a 6-inch stainless bowl with a magnet in the base. The magnet also holds the tray itself to a steel surface, so it can sit on the side of a toolbox or printer frame right where you work.

Pro tip Use one tray per assembly step and set them out in order. When it’s time to put things back together, the screws are already in the order they came out.

Why we like it

  • ✓Magnetic base holds steel screws, nuts and bits in place
  • ✓Stainless steel bowl, easy to wipe clean
  • ✓Round 6 in tray with raised sides
  • ✓Sticks to a steel bench, toolbox or car body

Keep in mind

  • !Only holds steel parts — brass, aluminum and most stainless screws won't stick
  • !Keep it away from phones, cards and hard drives; it is a strong magnet
Shape
Round bowl
Diameter
6 in (15 cm)
Depth
about 1.5 in
Material
Stainless steel, magnetic base
Model
67440
3 iFixit

iFixit Anti-Static Project Tray

One well per step, so a teardown goes back together in the right order.

Best for Phone and laptop repairselectronics teardownsgame controllerssmall appliance repairs

Electronics repairs fail at reassembly more often than at disassembly: a laptop can have screws in five different lengths, and putting a long one in the wrong hole can damage the board underneath. A sorting tray keeps each screw in its own spot, in the order it came out.

iFixit’s tray has 20 small wells in a grid and two large areas for the device and tools. It’s made from anti-static plastic, so it’s a sensible place to set down boards and ribbon cables, and at letter size it fits next to a repair mat.

Pro tip Work left to right, top to bottom, one well per step. Snap a phone photo of the tray next to the open device after each step — together they’re your reassembly guide.

Why we like it

  • ✓20 small compartments for screws and clips
  • ✓2 large compartments for a phone, tools or bigger parts
  • ✓Anti-static PET plastic for electronics work
  • ✓Letter-size footprint (11 × 8.5 in), thin enough to slide on a shelf
  • ✓iFixit lifetime warranty

Keep in mind

  • !Open tray, no lid — a bump sends small screws across the desk
  • !Shallow wells, meant for a single repair, not long-term storage
Size
11 × 8.5 × 0.5 in
Compartments
20 small + 2 large
Material
Anti-static PET plastic
Warranty
Lifetime (iFixit)
4 Flambeau

Flambeau 4007 Tuff Tainer with Zerust Dividers

A clear latching box with movable dividers that help keep steel parts from rusting.

Best for Screw and bolt assortmentssmall hardware kitsbead and craft partsparts that travel

Tackle boxes are made for small, sharp, metal things that need to stay sorted while they get carried around — which is exactly what a screw assortment is. A flat box with movable dividers lets you size the compartments to the parts, instead of the other way around.

The Tuff Tainer 4007 is a clear 11-inch box with 12 dividers. The dividers are made with Zerust, a corrosion inhibitor that Flambeau says protects bare metal inside a closed box for up to five years — handy for steel screws in a damp garage or basement.

Pro tip The rust protection works inside a closed container, so keep the lid latched. Store the box flat, and label the compartment edge, not the lid — lids get swapped.

Why we like it

  • ✓12 removable dividers, up to 24 compartments
  • ✓Zerust dividers release a vapor that Flambeau says inhibits rust
  • ✓Clear lid and base — you see the contents with the box closed
  • ✓Latching lid, flat enough to stack or slide onto a shelf
  • ✓Made in the USA

Keep in mind

  • !One open tray under the lid — drop it and every compartment mixes together
  • !Compartments are shallow, about 1.75 in deep in total
Size
11 × 7.25 × 1.75 in
Compartments
Up to 24
Dividers
12 Zerust (removable)
Material
Clear plastic
Closure
Latch
Model
4007
5 Brother

Brother P-touch PT-D220 Label Maker

Printed labels on every drawer and bin, so the system still works next month.

Best for Parts drawers and binscable and power supply labelstool casesshelf labels

Drawers and bins only stay organized if you can tell them apart at a glance. Masking tape and a marker works for a week; a printed label is readable from across the room and survives a few years of fingers and dust.

The PT-D220 is Brother’s everyday desktop labeler with a full QWERTY keyboard and a screen. It prints on laminated TZe tape up to about half an inch wide, one or two lines, and keeps 30 saved labels, so a run of “M3 × 8”, “M3 × 10”, “M3 × 12” is just edit and print.

Pro tip Put the size first and the type second (“M3 × 10 · button head”). The number is what your eye scans for, and the short label still fits on a small drawer front.

Why we like it

  • ✓Prints laminated TZe tape up to about 1/2 in (12 mm) wide
  • ✓QWERTY keyboard — faster than scrolling through letters
  • ✓1 or 2 lines of text, 14 fonts, 600+ symbols
  • ✓Saves up to 30 labels for reprinting
  • ✓Runs on batteries, so it goes to the shelf or the wall

Keep in mind

  • !Batteries (6 × AAA) and AC adapter are sold separately
  • !Only a sample tape is included — you'll need TZe tape right away
Tape
Brother TZe, up to 12 mm (~1/2 in)
Text
1–2 lines
Fonts
14 fonts, 11 styles
Memory
30 labels
Power
6 × AAA or optional AC adapter
Warranty
2-year limited
Model
PT-D220
6 Akro-Mils

Akro-Mils 30618 Louvered Steel Wall Panel (4-Pack)

Steel panels above the desk for open bins you can lift off and carry to the job.

Best for Wall above the benchbulk screws and fastenersfilament spares and nozzleskit parts by project

When the desk is full, the wall above it is the best storage space you have. A louvered panel turns it into a grid of slots for hanging bins — open-front boxes that hook on and lift off, so you can carry the one you need to the project.

The 30618 pack has four 18 × 19-inch steel panels, sized to fit above a normal desk or between studs. They take AkroBins in several sizes, and you can rearrange them any time without tools, which matters when a project’s parts outgrow a small bin.

Pro tip Screw the panels into studs, not just drywall — a row of full bins of steel screws gets heavy. Keep the heaviest bins on the bottom row, where they’re easier to lift off.

Why we like it

  • ✓16-gauge cold-rolled steel, powder-coated
  • ✓Four 18 × 19 in panels — line them up or split them between walls
  • ✓Hang AkroBins or Akro-Mils steel cabinets anywhere on the grid
  • ✓Open-front bins show the contents and need one hand
  • ✓Made in the USA

Keep in mind

  • !Bins are sold separately — the panels alone hold nothing
  • !Has to be screwed to the wall; not for renters who can't drill
Panel size
18 × 19 in (W × H)
Pack
4 panels
Material
16-gauge steel, powder-coated
Fits
AkroBins, Akro-Mils hanging cabinets
Color
Grey
Model
30618
7 Wall Control

Wall Control 30-P-3232B Metal Pegboard (2 Panels)

Steel pegboard behind the desk for drivers, pliers and parts cups.

Best for Wall behind the deskhand tools and driversparts bins and cupscable and spool storage

A pegboard behind the desk keeps the tools you reach for every day — drivers, tweezers, pliers, a few parts cups — off the work surface and in plain sight. Hardboard pegboard gets the job done, but its holes wear out, and hooks pop out every time you pull a tool.

Wall Control’s panels are steel with a mix of round holes and slots. Their own slotted hooks and bins lock into the slots, so they stay put. The panels have a 3/4-inch flange built in, so they mount straight to the wall with no frame. Two black 16 × 32-inch panels make about a 32-inch square above a normal desk.

Pro tip Hang the board so its bottom edge is a hand’s width above the desk. That leaves room for a monitor or cabinet in front of it, and you can still reach the lowest row while sitting.

Why we like it

  • ✓Two 16 × 32 in steel panels, about 32 × 32 in side by side
  • ✓Slotted holes take Wall Control's locking hooks, bins and shelves
  • ✓Steel holes don't wear out like hardboard pegboard
  • ✓Built-in 3/4 in flange — no spacers or frame needed
  • ✓Mounts into studs or drywall

Keep in mind

  • !Panels only — hooks, bins and shelves are sold separately
  • !Needs drilling into the wall
Panels
2
Panel size
16 × 32 in (W × H)
Depth
3/4 in flange
Material
Powder-coated steel
Color
Black
Model
30-P-3232B

More Maker Gear