Kraang Finds
More ▾
Products About
DIY

6 Clever Bathroom & Kitchen Fix-It Tools

Slow drains, a stubborn toilet, a dripping joint, moldy caulk, a weak faucet — six small tools that fix them without calling a plumber.

Published October 4, 2026 · 6 picks

Open bathroom vanity cabinet with small plumbing fix-it tools laid out on a towel

At a glance

6 picks
  1. 1
    FlexiSnake Drain Weasel Hair Clog Remover, Handle + 5 Wands
    Amazon
  2. 2
    Korky BeehiveMAX Heavy Duty Toilet Plunger 96-8A
    Amazon
  3. 3
    RIDGID 31175 Model 1017 Telescoping Basin Wrench, 10–17 in
    Amazon
  4. 4
    Mill-Rose 70660 Blue Monster PTFE Thread Seal Tape, 1/2 in x 260 in
    Amazon
  5. 5
    ALLWAY CT31 3-in-1 Caulk Tool
    Amazon
  6. 6
    Danco 11032 Faucet Aerator Key Set, 4 Sizes
    Amazon

As an Amazon Associate I earn from qualifying purchases. If you buy through a link on this page we may earn a small commission, at no extra cost to you. How this works.

1 FlexiSnake

FlexiSnake Drain Weasel Hair Clog Remover, Handle + 5 Wands

Pulls the hair clog out of a slow shower drain — no chemicals.

Best for Hair clogs in shower drainsbathtubs and bathroom sinks

A shower that drains slower every week usually isn’t a plumbing problem. It’s a plug of hair and soap scum sitting a few inches below the grate. Chemical drain cleaners try to dissolve it; this tool just grabs it and pulls it out.

The Drain Weasel is a thin, flexible wand covered in tiny hooks, clipped onto a handle that spins. Push it down the drain, twist the handle so the hair wraps around the hooks, and pull. FlexiSnake says the kit is made in the USA.

Pro tip Have a plastic bag ready before you pull the wand out — what comes up is not pretty. Then run hot water for a minute to flush loosened soap scum down the line.

Why we like it

  • ✓Thin micro-hook wand fits through most drain grates
  • ✓Rotating handle twists the wand to wrap up hair before pulling
  • ✓Five 18 in wands on a reusable quick-connect handle
  • ✓No chemicals — nothing harsh sitting in the pipes

Keep in mind

  • !Wands are disposable, so it's a consumable, not a one-time buy
  • !Reaches the first 18 in only — a clog deeper in the line needs a real drain auger
  • !Doesn't help with kitchen grease clogs
Wand length
18 in (46 cm)
Wands included
5
Handle
Rotating, quick-connect
Uses
Sinks, showers, tubs, grates
Model
DWPSK5A
2 Korky

Korky BeehiveMAX Heavy Duty Toilet Plunger 96-8A

A beehive cup that actually seals in a modern low-flow toilet.

Best for Toilet clogslow-flow (HET) and elongated bowlssmall bathrooms with no room for a plunger stand

The classic red cup plunger is a sink plunger. On a toilet, its flat rim can’t seal against the curved outlet, so most of the push just sloshes water around. Toilet plungers have a flange or a molded tip that sits inside the outlet, so the force actually goes down the drain.

The BeehiveMAX takes that idea further with a ribbed, beehive-shaped cup that compresses as you push. Korky designed it for today’s low-flow toilets, whose narrower outlets give older plungers trouble. The handle telescopes, so it can be stored under a vanity instead of sitting next to the toilet.

Pro tip Make sure the cup is covered by water before you plunge. Pushing water works much better than pushing air, and it splashes less. Start with a gentle first push to get the air out, then plunge firmly.

Why we like it

  • ✓Beehive-shaped cup seals into the toilet outlet like a flange plunger
  • ✓Korky says it fits both older and newer high-efficiency (HET) bowls
  • ✓Telescoping T-handle shortens for storage under the sink
  • ✓Rubber that won't mark the bowl

Keep in mind

  • !Toilet-only shape — a flat-cup plunger works better on sinks and tubs
  • !The telescoping joint is one more thing to rinse and dry after use
Cup
Rubber, beehive shape
Handle
Telescoping T-handle
Weight
10.2 oz (290 g)
Model
96-8A
3 RIDGID

RIDGID 31175 Model 1017 Telescoping Basin Wrench, 10–17 in

Reaches the faucet nuts hiding up behind the sink bowl.

Best for Removing and installing faucetssupply line nuts under sinkstight spaces behind basins

Replacing a faucet is an easy job right up to the moment you try to undo the nuts holding it on. They sit up behind the sink bowl, in the dark, with no room to swing a regular wrench. A basin wrench exists for exactly that spot: a long shank with a pivoting jaw at the top that grips the nut while you turn from below.

This one has a telescoping shank and a head that holds its angle, so you can set it, reach up, and ratchet the nut without the jaw flopping around. Flip the jaw over to switch between loosening and tightening.

Pro tip Turn off the water at the shut-off valves and open the faucet to release pressure before you start. A headlamp and a towel in the cabinet make the whole job much less miserable.

Why we like it

  • ✓Spring-loaded forged steel jaws ratchet one-handed
  • ✓Head pivots and holds its angle up to 90°
  • ✓Shank telescopes from 10 to 17 in
  • ✓3/8 to 1-1/4 in (10–32 mm) capacity
  • ✓RIDGID lists a lifetime warranty on material and workmanship

Keep in mind

  • !Does one job — under-sink nuts — and little else
  • !Jaws can chew up soft plastic faucet nuts; go easy on them
Length
10–17 in (25–43 cm), telescoping
Capacity
3/8–1-1/4 in (10–32 mm)
Jaws
Forged alloy steel, spring-loaded
Weight
0.9 kg (2 lb)
Model
31175
4 Mill-Rose

Mill-Rose 70660 Blue Monster PTFE Thread Seal Tape, 1/2 in x 260 in

A few wraps on the threads stop a shower arm or fitting from dripping.

Best for Shower armsthreaded pipe fittingshose bibswater and oil lines

Threaded pipe joints don’t seal on metal alone. The threads leave tiny spiral gaps, and water finds them. Thread seal tape fills those gaps and lubricates the threads so the joint can be tightened fully. It’s the fix for the classic drip where a shower arm goes into the wall or a hose bib connects to a pipe.

The Blue Monster is a well-known plumber’s version of the tape, on a 260-inch roll. For joints that keep weeping, many plumbers wrap the tape and then add a thin coat of pipe thread sealant (pipe dope) on top.

Pro tip Wrap clockwise when you’re looking at the end of the pipe — the same direction the fitting turns on — so tightening smooths the tape down instead of unrolling it. Three to four wraps is plenty; keep it off the first thread.

Why we like it

  • ✓PTFE fills the gaps between threads so the joint seals
  • ✓Rated from -450 to +500 °F (-268 to +260 °C)
  • ✓Mill-Rose says it has been used on fittings at up to 10,000 PSI
  • ✓260 in (6.6 m) roll covers a lot of small fittings

Keep in mind

  • !Not for oxygen lines (Mill-Rose warns against it)
  • !Gas lines call for gas-rated (yellow) tape — this isn't it
  • !Only for tapered pipe threads, not compression fittings or flare joints
Width
1/2 in (12.7 mm)
Length
260 in (6.6 m)
Material
PTFE
Temperature
-450 to +500 °F
Model
70660
5 ALLWAY

ALLWAY CT31 3-in-1 Caulk Tool

Cuts out the old caulk and smooths the new bead with one tool.

Best for Re-caulking tubsshowerssinks and windows

Moldy, peeling caulk around a tub makes the whole bathroom look dirty, and the fix is simple: take the old bead out completely and lay a fresh one. Most bad re-caulk jobs come from skipping the first part or smearing the second.

The CT31 covers both. A small stainless blade cuts the old caulk loose, a plastic scraper cleans up what’s left, and a rotating silicone tip shapes the new bead to one of three widths. It’s a small tool, but it turns a messy job into a neat one.

Pro tip After the old caulk is out, clean the joint with rubbing alcohol and let it dry completely. New caulk over soap scum or old silicone residue won’t stick, and it peels in a few weeks.

Why we like it

  • ✓Stainless steel blade cuts old caulk on a push or pull
  • ✓Silicone smoothing tip rotates to three bead sizes
  • ✓Plastic scraper for cleanup without scratching
  • ✓Works with acrylic, latex and silicone caulk

Keep in mind

  • !Hardened old silicone can still take some knife work and patience
  • !The blade can scratch acrylic tubs if you press too hard
Tools
Steel blade, silicone smoother, plastic scraper
Bead profiles
3 (narrow, medium, wide)
Body
Engineering plastic, soft grip
Weight
3.4 oz (95 g)
Model
CT31
6 Danco

Danco 11032 Faucet Aerator Key Set, 4 Sizes

Unlocks the hidden aerator so a weak, sputtering faucet flows again.

Best for Removing hidden (cache) aerators from kitchen and bathroom faucets for cleaning or replacement

When a faucet starts to spray sideways or the flow turns weak, the culprit is usually the aerator: the little screen at the tip of the spout, packed with mineral grit. Many newer faucets hide it inside the spout, with nothing to grip, so it takes a special key to get it out.

This Danco set has four keys for the common hidden sizes, color-coded and matched to coins on the listing: grey for standard (about a quarter), red for junior, green for tiny junior and yellow for tom thumb.

Pro tip Put the sink stopper in before you start — aerators are tiny and love drains. Soak the screen in white vinegar for an hour, brush it clean, and thread it back in by hand.

Why we like it

  • ✓Four color-coded keys for the common hidden aerator sizes
  • ✓Sizes compared to coins on the listing, so it's easy to pick the right one
  • ✓On a metal key ring — easy to keep in a drawer

Keep in mind

  • !Plastic keys — a stuck, scaled-up aerator may need a soak in vinegar first
  • !Only for hidden aerators; regular screw-on aerators need pliers instead
Keys
M24, M21.5, M18.5, M16.5
Material
Plastic, metal key ring
Length
2.5 in (6.4 cm)
Model
11032

More DIY